a better search for max devices

Stepper by dric: A 16-Step LFO for Any Live Parameter

· max4.live editorial

Most modulators in Max for Live pick a side. Either you get an LFO with a shape menu and a rate, or you get a step sequencer that outputs a value per step. Stepper by dric does both at once: it runs up to 16 steps, and each step holds its own waveform rather than a single flat value. The result is a modulator you can program like a pattern but that still moves inside each step.

It is filed as a MIDI Effect, which is the usual home for mapping devices in Live, but what it produces is parameter movement, not notes. Drop it on a MIDI track, hit map, click a parameter anywhere in your set, and Stepper drives it.

What the controls actually do

The front panel is small and the list of parameters is short, which is part of why it stays usable:

One practical note from the device's own documentation: to unmap, click the map button on and then off again. It is not obvious, and it is the kind of thing that costs ten minutes if nobody tells you.

The R button is the design decision that matters

Plenty of free LFO devices will modulate a parameter. The restart behaviour is what makes Stepper feel like an instrument rather than a background wobble. Because it lives on a MIDI track and watches incoming notes, the sequence can be locked to what you play instead of to the transport.

With R on and loop mode active, every note you play resets the modulation to step 1. That means the first step is always the attack of the sound — your filter position, your pitch offset, your grain size, whatever you mapped, starts from a known place every time. With R on and one-shot selected, you get an envelope you drew by hand: 16 steps of shape, fired per note, as long or short as the speed setting allows.

With R off, Stepper is a free-running LFO that drifts against your material. Both behaviours are useful; the switch between them is the whole workflow.

Three ways to put it in a session

A per-note envelope your synth doesn't have. Take a simple instrument rack — Operator, a sampler, anything with a parameter the built-in envelopes can't reach. Put Stepper ahead of it on the same track, set one-shot and R on, map it to that parameter, and set a short speed. Every note now carries a programmed contour. Because each step holds a waveform rather than a value, a four-step one-shot can do more than a four-point envelope: a sharp step, a ramp, a hold, a fall. It is particularly good on parameters Live's envelopes can't modulate at all, like a third-party plugin's macro or a send level.

Pattern modulation that fights the grid. Set R off, loop on, and seven steps. Map it to filter cutoff on a looping drum bus or a chord stab. Seven against sixteen takes a while to come back around, so a two-bar loop stops repeating identically without you drawing a single automation lane. Change the step count live and the relationship resets. This is the cheapest way to make a static clip move over eight bars.

Mix-level movement during a performance. Map Stepper to a send amount, a return device's dry/wet, or a Macro on an effects rack. Use bipolar depth and the offset control to centre the modulation where you want it, keep it in loop mode with R off, and then automate or map Stepper's own depth to a controller knob. Depth at zero means the parameter sits still; turning it up introduces the pattern you already programmed. That is a clean way to build a one-knob "bring in the chaos" control for a live set.

Where it sits next to comparable devices

The MIDI effect shelf at this popularity level is crowded, but the neighbours all do different jobs. CC map by veedjee is the obvious comparison for anyone mapping things: it is a bidirectional CC controller with MIDI learn, built to drive hardware over CC messages rather than to generate movement on its own. If your target is a synth outside the computer, CC map is the right tool and Stepper is not. There is a longer look at it in the CC map deep dive.

Tombola Sequencer by joelpowell is the other sequencer in this group, but it generates notes from a physics simulation — notes dropped into a rotating shape, with speed, mass, gravity and shape as the controls. It makes melodies; Stepper makes parameter curves. They stack well on the same track for that reason.

MotionMod by zealtv is the closest philosophical cousin: a modulation source that maps to Live parameters, except its input is a webcam detecting motion rather than a programmed sequence. It is expressive and unrepeatable, where Stepper is exact and repeatable. Humanizer by humanize is a different problem entirely — timing and velocity variation on existing MIDI — and its own page notes it has been superseded by a group version.

What the numbers tell you

19,591 downloads and a 5/5 rating across 16 comments is a strong combination. The rating is a small sample, as it always is on free device libraries, but a device that has been downloaded nearly twenty thousand times since 2016 and has not accumulated a visible complaint is a safe thing to install. It sits right alongside its comparison group in downloads — Humanizer, Tombola, CC map and MotionMod are all in the 19k–21k band — and only MotionMod rates lower at 4/5.

The release history is the thing to read carefully. Version 1.1 landed on 23 October 2016, one day after the original upload, and the only documented change is bipolar depth. That is a device that arrived close to finished and then stopped. The license is Attribution, which is about as permissive as these get.

Who should skip it

Stepper was built against Live 9.7 and Max 7.3.1 and has not been touched since 2016. Anything that old deserves a test pass in your current Live version before it goes anywhere near a show file — load it, map something, save, reopen, check the mapping survived. Mapping devices are the category most likely to be affected by changes in how Live exposes parameters, so do not discover a problem on stage.

Skip it, too, if what you want is a modulator with its own curve editor, MIDI-clock-synced divisions written as note values, or multiple simultaneous mapping targets from one instance. Stepper is one source to one destination, with a speed control rather than a sync menu. Run several instances if you need several targets.

And if your goal is to vary the feel of existing MIDI rather than to modulate a knob, this is the wrong shelf — look at transformation devices instead. For everyone else who has ever wanted a shape per step instead of a value per step, 16 steps and a restart button cover a surprising amount of ground.

More from the blog

All posts · Back to device search